СССР
Государственный стандарт от 30 марта 1990 года № ГОСТ 28500-90

ГОСТ 28500-90 (ИСО 5288-82) Передачи ременные синхронные. Термины и определения

Принят
Государственным комитетом СССР по управлению качеством продукции и стандартам
30 марта 1990 года
    ГОСТ 28500-90
    (ИСО 5288-82)
    Группа Г00
    МЕЖГОСУДАРСТВЕННЫЙ СТАНДАРТ
    ПЕРЕДАЧИ РЕМЕННЫЕ СИНХРОННЫЕ
    Термины и определения
    Synchronous belt drives. Terms and definitions
    МКС 01.040.21
    21.220.10
    ОКСТУ 0090; 4101
    Дата введения 1991-07-01
    ИНФОРМАЦИОННЫЕ ДАННЫЕ
    ВНЕСЕН Министерством нефтеперерабатывающей и нефтехимической промышленности СССР
    Постановлением Государственного комитета СССР по управлению качеством продукции и стандартам от 30.03.90 N 721 введен в действие государственный стандарт ГОСТ 28500-90, в качестве которого непосредственно применен международный стандарт ИСО 5288-82 с 01.07.91
    ПЕРЕИЗДАНИЕ. Октябрь 2005 г.
    якорь
    1.ОБЪЕКТ И ОБЛАСТЬ ПРИМЕНЕНИЯ
    Настоящий стандарт устанавливает термины и определения понятий в области синхронных ременных передач.
    Термины, установленные настоящим стандартом, обязательны для применения во всех видах документации и литературы, входящих в сферу работ по стандартизации или использующих результаты этих работ.
    В таблице приведены термины с определениями на трех официальных языках ИСО - русском, английском и французском.
    В таблице к ряду терминов приведены буквенные обозначения и чертежи.
    В стандарте приведены алфавитные указатели содержащихся в нем терминов на английском, французском и русском языках. Кроме того, в качестве справочных приведены алфавитные указатели терминов-эквивалентов на немецком и итальянском языках.
    Термины и определения, относящиеся к синхронным ременным передачам
    Таблица
    Термин Обозна- чение Определение Чертеж
    2 General definitions Общие определения
    2.1 synchronous belt drive A system composed of a synchronous belt and two or more synchronous pulleys. Synchronized motion and/or power is transmitted through the engagement of teeth on the belt with teeth on the pulleys
    transmission par courroie synchrone d'une courroie synchrone et d'au moins deux poulies synchrones. La rotation ou la puissance est transmise par des dents de la courroie avec celles des poulies
    синхронная ременная передача Передача, состоящая из синхронного ремня и не менее двух синхронных шкивов; мощность или вращение передаются посредством зацепления зубьев ремня с зубьями шкивов
    2.2 centre distance The shortest distance between the axes of two synchronous pulleys when the belt is under the prescribed measuring force
    entr'axe Plus courte distance entre les axes de deux poulies synchrones lorsque la courroie supporte l'effort de mesure prescrit
    межосевое расстояние Самое короткое расстояние между осями двух синхронных шкивов, когда ремень находится под требуемым натяжением
    3 Definitions relating to synchronous belts concernant les courroies synchrones Определения, относящиеся к синхронным ремням
    3.1 Belts, general Courroies, Ремни, общая часть
    3.1.1 synchronous belt A belt, the cross section of which is in the general form of a rectangle, but with transverse teeth extending from the lower base at regularly spaced intervals
    courroie synchrone Courroie dont la section droite la forme d'un rectangle mais qui comporte des intervalles des dents transversales sous sa face
    синхронный ремень Ремень, прямое сечение которого имеет форму прямоугольника, на внутренней стороне которого расположены на равном расстоянии друг от друга поперечные зубья трапециевидного профиля
    3.1.2 belt pitch The linear distance between the axes of two consecutive teeth in a section of belt loaded to the prescribed measuring force
    pas Distance entre les axes de de deux dents dans une portion rectiligne de courroie supportant l'effort prescrit de mesure
    шаг Расстояние между осями симметрии двух последовательных зубьев на прямолинейном участке ремня, находящемся под заданным натяжением
    3.1.3 pitch line Any circumferential line in the belt which keeps the same length when the belt is bent perpendicularly to its base
    ligne primitive Toute ligne de courroie qui conserve sa longueur lorsque la courroie est perpendiculairement sa base
    расчетная линия Любая круговая линия ремня, сохраняющая свою длину, когда ремень сложен перпендикулярно к основанию
    3.1.4 pitch length longueur primitive The length of the pitch line of a belt Longueur de la ligne primitive d'une courroie
    расчетная длина Развернутая длина расчетной линии ремня
    3.1.5 width The transverse dimension of the belt that can be used to transmit power
    largeur Dimension transversale de la courroie dont la puissance transmissible
    ширина Поперечный размер ремня, от которого зависит передаваемая мощность
    3.1.6 height The total height of the belt
    hauteur Hauteur ou totale de la courroie
    высота Высота или общая толщина ремня
    3.2 Synchronous belt teeth
    Dents de courroie synchrone
    Зубья синхронного ремня
    3.2.1 tooth One of the transverse elements protruding from the bottom of the belt having the profile to mesh with the teeth in a synchronous pulley
    dent Un des transversaux faisant saillie sous la face de la courroie et ayant Ie profil pour engrener avec les dents d'une poulie synchrone
    зубья Поперечные элементы, расположенные на внутренней поверхности ремня, для сцепления с зубьями синхронного шкива
    3.2.2 tip line Line joining the apices of the belt teeth
    ligne de Ligne joignant les sommets de dents d'une courroie l'ахе longitudinal de celle-ci
    верхняя линия Линия, соединяющая вершины зубьев ремня параллельно его продольной оси
    3.2.3 root line Line joining the low points between the teeth of a belt
    ligne de pied Ligne joignant les bases de dents d'une courroie l'axe longitudinal de celle-ci
    нижняя линия Линия, соединяющая основания зубьев ремня параллельно его продольной оси
    3.2.4 tooth height Distance between the tip line and the root line
    hauteur de dent Distance comprise entre une ligne de et une ligne de pied pour une courroie, ces deux lignes dans la section droite longitudinale de la courroie
    высота зубьев Расстояние между верхней и нижней линиями одного зуба, расположенными на одном и том же продольном прямом сечении ремня
    3.2.5 flank Area defined by the width of the belt and the straight portion of the tooth section contained between the tip line and the root line
    flanc Surface par la largeur de la courroie et la partie rectiligne de la dent comprise entre la ligne de et la ligne de pied
    боковая поверхность Участок, образующийся между внутренней и наружной поверхностями
    3.2.6 mating flank Flank of the belt tooth that is in contact with the pulley tooth
    flanc en contact Celui des deux flancs de la dent d'une courroie qui touche une dent de poulie
    боковая контактирующая поверхность Боковая поверхность зуба ремня, которая соприкасается с зубом шкива
    3.2.7 working flank Flank of a belt tooth used to transmit motion to or from the pulley
    flanc actif Celui des deux flancs d'une dent de courroie qui recoit Ie mouvement ou Ie transmet une poulie
    активная боковая поверхность Та из двух боковых поверхностей зуба ремня, которая передает движение шкиву или принимает от шкива
    3.2.8 non-working flank Flank of tooth opposite the working flank
    flanc inactif Flanc d'une dent de courroie au flanc actif
    неактивная боковая поверхность Другая боковая поверхность того же зуба
    3.2.9 radius at tooth tip Radius of a curve connecting the tooth flank with the tip line
    rayon en de dent Rayon de l'arrondi reliant la section d'un flanc de dent sa ligne de
    радиус в верхней части зуба Радиус закругленной части, соединяющий сечение боковой поверхности зуба с его верхней линией
    3.2.10 radius at tooth root Radius of a curve connecting the tooth flank witn the root line
    rayon au pied de dent Rayon de l'arrondi reliant la section d'un flanc de dent sa ligne de pied
    радиус у основания зуба Радиус закругленной части, соединяющей сечение боковой поверхности зуба с его нижней линией
    3.2.11 width at tooth root Linear distance between the theoretical points of intersection of the tooth flanks with the root line when the belt is straight
    largeur au pied de dent Distance comprise entre les points d'intersection des flancs d'une dent avec sa ligne de pied, lorsque la portion de la courroie est rectiligne
    ширина у основания зуба Расстояние между теоретическими точками пересечения боковых поверхностей зуба с его нижней линией, когда рассматриваемый участок ремня прямолинейный
    3.2.12 tooth angle 2 Included angle between the flanks of the belt tooth
    angle de dent Angle compris entre les deux flancs d'une dent de courroie
    угол зуба Угол между обеими боковыми поверхностями зуба ремня
    4 Definitions relating to synchronous pulleys concernant les poulies synchrones Определения, относящиеся к синхронным шкивам
    4.1 Pulleys, general Poulies, Шкивы, общая часть
    4.1.1 synchronous pulley Pulley with transverse teeth equally spaced around its circumference
    poulies synchrone Poulie munie sa de dents transversales
    синхронный шкив Шкив, имеющий на своей окружности поперечные равноотстоящие зубья
    4.1.2 pitch reference cylinder Imaginary cylindrical surface, coaxial to a pulley, with reference to which the dimensions of the tooth space of a pulley are defined
    cylindre primitif Cylindre de fictif, coaxial la poulie, et servant les cotes des dents de la poulie et de leurs intervalles
    расчетная цилиндрическая поверхность Воображаемая цилиндрическая поверхность, соосная со шкивом и служащая для определения размеров зубьев шкива и расстояния между ними*
    ________________ * См. 4.2.2 для определения расстояния между зубьями.
    4.1.3 pitch circle Section of a pitch reference cylinder with a plane perpendicular to the axis of the pulley
    cercle primitif Section du cylindre primitif par un plan perpendiculaire l'axe de la poulie
    расчетная окружность Сечение расчетной поверхности с плоскостью, перпендикулярной к оси шкива
    4.1.4 outside diameter Diameter of the tip circle
    du cercle de
    наружный диаметр Диаметр верхней окружности*
    ________________ * Cм. 4.2.4 для определения верхней окружности.
    4.1.5 pitch diameter Diameter of the pitch circle
    primitif du cercle primitif
    расчетный диаметр Диаметр расчетной окружности
    4.1.6 pitch line differential Radial distance between the pitch circle and the tip circle
    de ligne primitive Distance suivant un rayon entre Ie cercle primitif et Ie cercle de
    положение расчетной линии Расстояние, измеренное по радиусу между расчетной окружностью и верхней окружностью
    4.1.7 pitch Length of arc on the pitch circle contained between two consecutive corresponding profiles
    pas Longueur Ie l'arc du cercle primitif compris entre les points homologues de deux dents
    шаг* Длина дуги расчетной окружности между соответствующими точками двух последовательных зубьев
    ________________ * Рассматриваемый как отрезок зубчатой рейки, шаг шкива соответствует шагу ремня.
    4.1.8 minimum pulley width Smallest lateral distance across the face of a pulley (or between the flanges of a flanged pulley) that can be used for a stated belt width
    largeur minimale de poulie Plus petite distance axiale entre les deux faces d'une poulie, ou entre les flasques d'une poulie , qui puisse pour une courroie de largeur
    минимальная ширина Наименьшее осевое расстояние между обеими поверхностями шкива или между фланцами шкива, которое может быть использовано для ремня заданной ширины
    4.1.9 measuring pulley Pulley specifically machined or selected to permit precise length measurement of a synchronous belt
    poulie de mesure Poulie ou choisie pour permettre de mesurer avec la longueur d'une courroie synchrone
    измерительный шкив Изготовленный или специально подобранный шкив для прецизионного измерения длины синхронного ремня
    4.1.10 measuring pulley tooth clearance Shortest distance between nonworking flanks of belt and measuring pulley teeth, when the working flanks are in contact
    jeu de denture sur la poulie de mesure Plus petite valeur de la distance les flancs inactifs d'une dent de la courroie et de la dent voisine de la poulie, lorsque les flancs actifs sont en contact l'un avec l'autre
    зубчатый зазор на измерительном шкиве Наименьшее расстояние, разделяющее неактивные боковые поверхности зуба ремня и зуба шкива, когда активные боковые поверхности контактируют друг с другом
    4.2 Synchronous pulley teeth Dents de poulie synchrone Зубья синхронного шкива
    4.2.1 teeth Equally spaced transverse protrusions with which the belt teeth mesh to provide a transfer of force between the belt and the pulley
    dents transversaux qui font saillie la d'une poulie et avec lesquels les dents d'une courroie pour transmettre un effort tangential de l'une l'autre
    зубья Равностоящие поперечные элементы, выступающие на окружности шкива, с которыми зубья ремня образуют зацепление для передачи тангенциального усилия
    4.2.2 tooth space Space between two adjacent teeth of a pulley
    intervalle Intervalle entre deux dents d'une poulie
    пространство между зубьями Расстояние между двумя последовательными зубьями шкива
    4.2.3 tip cylinder Surface coaxial with the pulley containing the crests of the teeth
    cylindre de Surface coaxiale a la poulie et contenant les sommets ou de dents
    верхняя цилиндрическая поверхность Поверхность, соосная со шкивом на уровне вершин зубьев
    4.2.4 tip circle Section of the tip cylinder whose plane is perpendicular to the axis of the pulley
    cercle de Section droite du cylinder de
    верхняя окружность Прямое сечение верхней цилиндрической поверхности
    4.2.5 root cylinder Surface coaxial with the pulley containing the bottom of the tooth spaces
    cylindre de pied Surface coaxiale la poulie et tangente au fond des intervalles
    нижняя цилиндрическая поверхность Поверхность, соосная со шкивом и касательная к основанию зубьев
    4.2.6 root circle Section of the root cylinder whose plane is perpendicular to the axis of the pulley
    cercle de pied Section droite du cylindre de pied
    нижняя окружность Прямое сечение нижней цилиндрической поверхности
    4.2.7 tooth space depth Radial distance between the tip circle and the root circle
    profondeur de I'intervalle Dimension Ie long d'un rayon entre un cercle de et un cercle de pied dans Ie plan
    глубина пространства между зубьями Расстояние, определяемое по радиусу между верхней и нижней окружностями, расположенными в одной плоскости
    4.2.8 flank Area defined by the width of the pulley and the involute (or straight) portion of a pulley tooth contained between the tip cylinder and the root cylinder
    flanc Une des surfaces par la largeur de la poulie et par la partie en de cercle (ou rectiligne) de la dent qui est comprise entre Ie cylinder de et Ie cylindre de pied
    боковая поверхность Одна из поверхностей, ограниченных шириной шкива и верхней и нижней поверхностями цилиндра (или прямолинейными участками)
    4.2.9 mating flank Flank of the pulley tooth that is in contact with the belt
    flanc en contact Flanc d'une dent de poulie qui touche une dent de courroie
    боковая контактирующая поверхность Боковая поверхность зуба шкива, соприкасающаяся с зубом ремня
    4.2.10 working flank Flank of the pulley tooth used to transmit motion to or from the belt
    flanc actif Flanc d'une dent de poulie qui Ie mouvement ou Ie transmet la courroie
    активная боковая поверхность Боковая поверхность зуба шкива, передающая движение ремню или принимающая его
    4.2.11 non-working flank Flank of the pulley tooth opposite the working flank
    flanc inactif Flanc d'une dent de poulie au flanc actif
    неактивная боковая поверхность Другая боковая поверхность того же зуба
    4.2.12 radius at the tooth tip Radius of a curve connecting the tooth flank with the tip circle
    rayon en de dent Rayon de l'arrondi reliant la section d'un flanc de dent a sa ligne de
    радиус у вершины зуба Радиус закругления, соединяющего сечение боковой поверхности зуба с верхней окружностью
    4.2.13 radius at the tooth root Radius of a curve connecting the tooth flank with the root circle
    rayon au pied de dent Rayon de l'arrondi reliant la section d'un flanc de dent sa ligne de pied
    радиус у основания Радиус закругления, соединяющего сечение боковой поверхности зуба с нижней окружностью
    4.2.14 width at tooth space root Linear distance between the theoretical points of intersection of the tooth space flanks with the root circle
    largeur au pied de dent Distance suivant une corde entre les points d'intersection du cercle de pied avec les flancs, se faisant face, de deux dents
    ширина основания зуба Расстояние, измеренное по хорде между теоретическими точками пересечения нижней окружности с боковыми поверхностями, расположенными напротив двух соседних зубьев
    4.2.15 tooth space angle 2 Included angle between the flanks of the tooth space
    angle au sommet de l'intervalle Angle compris entre les flancs, se faisant face, de deux dents
    угол пространства между зубьями Угол между боковыми поверхностями двух соседних зубьев
    4.3 Synchronous pulley involute tooth generating tools de pour dents de poulie en Стандартная кремальера для зубьев шкива в развертке
    4.3.1 rack Toothed member having the form of a rectangular bar, whose teeth may be superimposed by rectilinear translation
    Organe de forme , et portant sur une de ses faces une de dents superposables par translation rectiligne
    кремальера Элемент в форме параллелепипеда, несущий на одной из своих поверхностей ряд одинаковых равноотстоящих зубьев
    4.3.2 reference rack Rack whose profile is used as the base of a standardized system of pulleys having the same generating rack
    de dont la section perpendiculaire aux des dents sert les dimensions des dents en d'un de poulies
    эталонная кремальера Вымышленная кремальера, сечение которой перпендикулярно к ребрам зубьев и служит для определения нормализованных размеров зубьев в развертке той же системы шкивов
    4.3.3 reference rack: pitch line Line, with reference to which the dimensions of the rack teeth are defined
    ligne primitive de la de Ligne par rapport a laquelle sont les dimensions des dents de la de
    расчетная линия эталонной кремальеры Линия, по отношению к которой определяются размеры зубьев эталонной кремальеры
    4.3.4 reference rack: root line Line joining the low points between the teeth of a rack
    ligne de pied de la de Ligne reliant les fonds des dents d'une section longitudinale de la
    нижняя линия эталонной кремальеры Линия, соединяющая поверхности кремальеры, расположенные между зубьями, в продольном сечении эталонной кремальеры
    4.3.5 reference rack: tip line Line joining the tips of the teeth of a rack
    ligne de de la de Ligne reliant les des dents d'une section longitudinale de la
    верхняя линия эталонной кремальеры Линия, соединяющая верхние поверхности зубьев, в продольном сечении эталонной кремальеры
    4.3.6 reference rack: flank Portion of the rack tooth contained between the tip line and the root line
    flanc d'une dent de la de Partie d'une dent de la de qui est comprise entre la ligne de et la ligne de pied
    боковая поверхность зуба эталонной кремальеры Часть зуба эталонной кремальеры между уровнем верхней и нижней линии
    4.3.7 reference rack: pitch line location Distance between the pitch line and the root line of the rack
    de la ligne primitive de la de Distance comprise entre la ligne primitive de la de et sa ligne de pied
    расположение расчетной линии эталонной кремальеры Расстояние между расчетной линией эталонной кремальеры и нижней линией
    4.3.8 reference rack: pitch Linear distance between the centre of two adjacent teeth on the rack
    pas de la de Distance comprise entre les axes de de deux dents de la de
    шаг эталонной кремальеры Расстояние между осями симметрии двух последовательных зубьев эталонной кремальеры
    4.3.9 reference rack: tooth angle 2 Included angle between the flanks of the tooth of the rack
    angle de la dent de la de Angle par les deux flancs d'une dent de la de
    угол у вершины зуба эталонной кремальеры Угол между двумя боковыми поверхностями зуба эталонной кремальеры
    4.3.10 reference rack: tooth height Distance between the tip line and the root line of the rack
    hauteur de dent de la de Distance comprise entre une ligne de et une ligne de pied dans la section droite longitudinale de la de
    высота зуба эталонной кремальеры Расстояние между верхней и нижней линиями, расположенными в одном и том же прямом продольном сечении эталонной кремальеры
    4.3.11 reference rack: width at tooth tip Linear distance between the theoretical points of intersection of the tooth flanks with the tip line of the rack
    largeur en de dent de la de Dans une section droite longitudinale de la de , distance comprise entre les points d'intersection des flancs d'une dent avec la ligne de
    ширина в верхней части зуба эталонной кремальеры Расстояние между теоретическими точками пересечения боковых поверхностей зуба с верхней линией в прямом продольном сечении кремальеры
    4.3.12 reference rack: radius at tooth tip Radius of a curve connecting the tooth flank with the tip line of the rack
    rayon en d'une dent de la de Dans une section droite longitudinale de la de , rayon de l'arrondi reliant un flanc de dent la ligne de
    радиус в верхней части зуба эталонной кремальеры Радиус закругления, соединяющего боковую поверхность зуба с верхней линией в прямом продольном сечении эталонной кремальеры
    4.3.13 reference rack: radius at tooth root Radius of a curve connecting the tooth flank with the root line of the rack
    rayon au pied d'une dent de la de Dans une section droite longitudinale de la de , rayon de l'arrondi reliant un flanc de dent la ligne de pied
    радиус у основания зуба эталонной кремальеры Радиус закругления, соединяющего боковую поверхность зуба с нижней линией в прямом продольном сечении эталонной кремальеры
    якорь
    АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА АНГЛИЙСКОМ ЯЗЫКЕ
    В
    Belt pitch 3.1.2
    Belts 3.1
    С
    Centre distance 2.2
    F
    Flank 3.2.6, 4.2.8
    Н
    Height 3.1.6
    М
    Mating flank 3.2.6, 4.2.9
    Measuring pulley 4.1.9
    Measuring pulley tooth clearance 4.1.10
    Minimum pulley width 4.1.8
    N
    Non-working flank 3.2.8, 4.2.11
    О
    Outside diameter 4.1.4
    Р
    Pitch 4.1.7
    Pitch circle 4.1.3
    Pitch diameter 4.1.5
    Pitch length 3.1.4
    Pitch line 3.1.3
    Pitch line differential 4.1.6
    Pitch reference cylinder 4.1.2
    Pulleys 4.1
    R
    Rack 4.3.1
    Radius at tooth line 4.2.12
    Radius at tooth root 3.2.10
    Radius at tooth tip 3.2.9, 4.2.12
    Reference rack 4.3.2
    flank 4.3.6
    pitch 4.3.8
    pitch line 4.3.3
    pitch line location 4.3.7
    radius at tooth tip 4.3.12
    radius at tooth root 4.3.13
    root line 4.3.4
    tip line 4.3.5
    tooth angle 4.3.9
    tooth height 4.3.10
    width at tooth tip 4.3.11
    Root circle 4.2.6
    Root line 3.2.3
    S
    Synchronous belt 3.1.1
    Synchronous belt drive 2.1
    Synchronous pulley 4.1.1
    Synchronous pulley teeth 4.2
    Synchronous pulley involute tooth generating tools 4.3, 3.2
    Т
    Tip circle 4.2.4
    Tip cylinder 4.2.3
    Tip line 3.2.2
    Teeth 4.2.1
    Tooth 3.2.1
    Tooth angle 3.2.12
    Tooth height 3.2.4
    Tooth space 4.2.2
    Tooth space angle 4.2.15
    Tooth space depth 4.2.7
    W
    Width 3.1.5
    Width at tooth root 3.2.11
    Width at tooth space root 4.2.14
    Working flank 3.2.7, 4.2.10
    якорь
    АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА ФРАНЦУЗСКОМ ЯЗЫКЕ
    А
    angle au sommet de l'intervalle 4.2.15
    angle de dent 3.2.12
    angle de la dent de la de 4.3.9
    С
    cercle de pied 4.2.6
    cercle de 4.2.4
    cercle primitif 4.1.3
    courroies 3.1
    courroie synchrone 3.1.1
    4.3.1
    de 4.3.2
    de pour dents de poulie en 4.3
    cylindre de pied 4.2.5
    cylindre de 4.2.3
    cylindre primitif 4.1.2
    D
    4.1.4
    primitif 4.1.5
    dent (s) 3.2.1, 4.2.1
    dents de courroie synchrone 3.2
    dents de poulie synchrone 4.2
    de ligne primitive de la de 4.3.7
    de la ligne primitive 4.1.6
    Е
    entr'axe 2.2
    F
    flanc 3.2.5, 4.2.8
    flanc actif 3.2.7, 4.2.10
    flanc d'une dent de la de 4.3.6
    flanc en contact 3.2.6, 4.2.9
    flanc inactif 3.2.8, 4.2.11
    H
    hauteur 3.1.6
    hauteur de dent 3.2.4
    hauteur de dent de la de 4.3.10
    I
    intervalle 4.2.2
    J
    jeu de denture sur la poulie de mesure 4.1.10
    L
    largeur 3.1.5
    largeur au pied de dent 3.2.10, 4.2.14
    largeur en de dent de la de 4.3.11
    largeur minimale de poulie 4.1.8
    ligne de pied 3.2.3
    ligne de pied de la de 4.3.4
    ligne de 3.2.2
    ligne de de la de 4.3.5
    ligne primitive 3.1.3
    ligne primitive de la de 4.3.3
    P
    pas 3.1.2, 4.1.7
    de la de 4.3.8
    poulies 4.1
    poulie de mesure 4.1.9
    poulie synchrone 4.1.1
    profondeur de l'intervalle 4.2.7
    R
    rayon au pied de dent 3.2.10, 4.2.13
    rayon en de dent 3.2.9, 4.2.12
    rayon au pied d'une dent de la de 4.3.13
    rayon en d'une dent de la de 4.3.12
    Т
    transmission par courroie synchrone 2.1
    якорь
    АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА РУССКОМ ЯЗЫКЕ
    зубья синхронного ремня 3.2, 3.2.1
    боковая поверхность 3.2.5
    боковая поверхность активная 3.2.7
    боковая поверхность контактирующая 3.2.6
    боковая поверхность неактивная 3.2.8
    верхняя линия 3.2.2
    высота зубьев 3.2.4
    нижняя линия 3.2.3
    радиус в верхней части зуба 3.2.9
    радиус у основания зуба 3.2.10
    угол зуба 3.2.12
    ширина у основания зуба 3.2.11
    зубья синхронного шкива 4.2, 4.2.1
    боковая поверхность 4.2.8
    боковая поверхность активная 4.2.10
    боковая поверхность контактирующая 4.2.9
    боковая поверхность неактивная 4.2.11
    верхняя цилиндрическая поверхность 4.2.3
    верхняя окружность 4.2.4
    глубина пространства между зубьями 4.2.7
    пространство между зубьями 4.2.2
    радиус у вершины зуба 4.2.12
    радиус у основания 4.2.13
    ширина основания зуба 4.2.14
    угол пространства между зубьями 4.2.15
    К
    кремальера 4.3.1
    боковая поверхность зуба эталонной кремальеры 4.3.6
    верхняя линия эталонной кремальеры 4.3.5
    высота зуба эталонной кремальеры 4.3.10
    нижняя линия эталонной кремальеры 4.3.4
    радиус в верхней части зуба эталонной кремальеры 4.3.12
    радиус у основания зуба эталонной кремальеры 4.3.13
    расчетная линия эталонной кремальеры 4.3.3
    расположение расчетной линии эталонной кремальеры 4.3.7
    угол у вершины зуба эталонной кремальеры 4.3.9
    шаг эталонной кремальеры 4.3.8
    ширина в верхней части зуба эталонной кремальеры 4.3.11
    эталонная 4.3.2
    Р
    расстояние межосевое 2.2
    ремни 3
    высота 3.1.6
    зубья синхронного ремня 3.2
    общая часть 3.1
    расчетная длина 3.1.4
    расчетная линия 3.1.3
    синхронные 3.1.1
    шаг 3.1.2
    ширина 3.1.5
    С
    синхронная ременная передача 2.1
    синхронные ремни 3
    Ш
    шкивы 4.1
    зубчатый зазор на измерительном шкиве 4.1.10
    зубья синхронного шкива 4.2
    измерительный шкив 4.1.9
    минимальная ширина 4.1.8
    наружный диаметр 4.1.4
    расчетный диаметр 4.1.5
    расчетная окружность 4.1.3
    расчетная цилиндрическая поверхность 4.1.2
    синхронные 4.1.1
    якорь
    АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА НЕМЕЦКОМ ЯЗЫКЕ
    А
    Arbeitsflanke 3.2.7, 4.2.10
    4.1.4
    В
    Bezugsprofil 4.3.2
    Bezugszahnstange 4.3.2
    Breite 3.1.5
    Breite am 3.2.11
    Breite am Zahnkopf 4.3.11
    Breite am 4.2.14
    F
    Flanke 3.2.5, 4.2.8, 4.3.6
    Hankenspiel in der 4.1.10
    4.2.6
    3.2.3, 4.3.4
    4.2.5
    G
    Gegenflanke 3.2.6, 4.2.9
    H
    3.1.6
    К
    Kopfkreis 4.2.4
    Kopflinie 3.2.2, 4.3.5
    Kopfzylinder 4.2.3
    L
    Lage der Wirklinie 4.3.7
    M
    4.1.9
    Mittenabstand 2.2
    R
    Radius am 3.2.10, 4.2.13, 4.3.13
    Radius am Zahnkopf 3.2.9, 4.2.12, 4.3.12
    Riemen 3.1
    Riemenzahnteilung 3.1.2
    3.2.8, 4.2.11
    S
    Scheibe 4.1
    Scheibenbreite, Mindest 4.1.8
    Synchronriemen 3.1.1
    Synchronriementrieb 2.1
    Synchronscheibe 4.1.1
    Т
    Teilung 4.1.7, 4.3.8
    Teilungs-Bezugszylinder 4.1.2
    W
    Wirkdurchmesser 4.1.5
    Wirkkreis 4.1.3
    3.1.4
    Wirklinie 3.1.3, 4.3.3
    Wirklinien-Differenz 4.1.6
    Z
    Zahn 3.2.1, 4.2.1
    3.2.4, 4.3.10
    4.2.2
    4.2.7
    4.2.15
    Zahnstange 4.3.1
    Zahnteilung 3.1.2, 4.1.7
    Zahnwinkel 3.2.12, 4.3.9
    якорь
    АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА ИТАЛЬЯНСКОМ ЯЗЫКЕ
    А
    altezza 3.1.6
    altezza del dente 3.2.4, 4.3.10
    angolo del dente 3.2.12, 4.3.9
    angolo del vano 4.2.15
    С
    cerchio di fondo 4.2.6
    cerchio di troncatura 4.2.3, 4.2.4
    cilindro di fondo 4.2.5
    cilindro primitivo di riferimento 4.1.2
    cinghie, 3.1
    cinghia sincrona 3.1.1
    circonferenza primitiva 4.1.3
    cremagliera 4.3.1, 4.3.2
    D
    dente 3.2.1, 4.2.1
    dentatura cinghia sincrona 3.2
    dentatura puleggia sincrona 4.2
    diametro esterno 4.1.4
    diametro primitivo 4.1.5
    F
    fianco 3.2.5, 4.2.8, 4.3.6
    fianco attivo 3.2.7, 4.2.10
    fianco a contatto 3.2.6, 4.2.9
    fianco inattivo 3.2.8, 4.2.11
    G
    cremagliera di riferimento per dentatura puleggia ad evolvente 4.3
    gioco nella dentatura delle puleggia di misura 4.1.10
    L
    larghezza 3.1.5
    larghezza sul fondo del dente 3.2.11
    larghezza alla del dente 4.3.11
    larghezza minima 4.1.8
    larghezza sul fondo del vano 4.2.14
    linea di fondo 3.2.3, 4.3.4
    linea di troncatura 3.2.2, 4.3.5
    linea primitiva 3.1.3, 4.3.3
    lunghezza primitiva 3.1.4
    Р
    passo 3.1.12, 4.1.7, 4.3.8
    pulegge 4.1
    puleggia di misura 4.1.9
    puleggia sincrona 4.1.1
    del vano 4.2.7
    posizione linea primitiva 4.3.7
    Q
    quota radiale primitiva 4.1.6
    R
    raccordo alla del dente 3.2.9, 4.2.12, 4.3.12
    raccordo sul fondo del dente 3.2.10, 4.2.13, 4.3.13
    V
    vano 4.2.2